Super Installer Lite

Super Installer Lite

Emitor´s Super Installer Lite is developed in Sweden for exact alignment and adjustment of satellite dishes. It is designed to be extremely easy to use. Simply select the satellite you want to find or install and the meter will try to identify that satellite only.
When finding the satellite the meter will show exact digital readouts for SNR and Quality in order to get a perfect result of the installation. The Super Installer Lite is microprocessor controlled, making it very reliable and accurate. Signal strength is presented on the LCD-display.
The meter searches for one satellite at a time in "Satellite Search" mode. You can also choose to view the signal in spectrum mode.
The Super Installer Lite is very sensitive and can detect even the weakest signals. The instrument can supply Voltage (13/18/21 Volt), 22 kHz and DiSEqC for directconnection to LNBs. The meter is short-circuit protected by an automatic current sensing circuit.

Technical specification
• Input frequency: 920-2150MHz
• Input level: 35-100 dBuV
• Input/output impedance: 75 Ohm, F-connector
• Measuring method (Analog):
• RF Signal presentation in thermometer scale.
• Loudspeaker tone changes with signal level when enabled
• Measuring method (Digital):
• Quality (derived from BER - bit error rate)
• SNR (signal/noise-ratio)
• Scales showing max signal and max values
• EasyFind satellite identification: By using the Symbol Rate / FEC in the
signal and the ONID/TSID in the transport stream
• Search automatically acquires DVB-S transponders using advanced
demodulator to determine FEC and Symbol Rate.
• Spectrum Analyzer 950 MHz to 2150 MHz.
• Backlit 128x64 Pixels LCD.
• PC connection: RS232 with DB9 connector
• LNB Power: 13V or 18V. 21V selectable.
• 22 kHz tone: Standard 22 KHz signal superimposed at 0.65V p-p on LNB-A
• DiSEqC: Yes, according to 1.0.
• Battery: Rechargeable NiMH battery pack.
• Battery Life: About 1 hour on fully charged batteries.
• Weight: About 0.7 kg including batteries.
• Accessories: Orange rubber casing.
• Power-supply of 100-240VAC 12V, 1.2 A
• Car-charger
 

The Super Installer Lite is equipped with the NEW "Fast Track" chip making it the fastest most reliable satellite meter in its class.

No more guessing with the "LOCKED" (FOUND) feature! It will positively ID the satellite you are looking for. 

The Super Installer Lite can power the new DirecTV SWM 21V satellite LNB. No need to power the unit with a power supply or satellite receiver. Unit comes with DirecTv and Dish Network files built in.

Super Installer Lite Identifies the following satellites:

•   DIRECTV
• 101W  Slimline KA/KU,
• 101W  Slimline SWM 21V
• 110W  Slimline KA/KU
• 119W  Slimline KA/KU
• 119W  Slimline SWM 21V
• 72W   Ku 18V
•   DISH NETWORK
• 61W KU
• 110W Dish 500 KU
  
• 119W Dish 500 KU
• 100W Dish 1000.2 Dishes
• 119W Dish 1000.2 Dishes
• 129W Dish 1000.2 Dishes
• 118.7W Dish KU
•   BELL EXPRESSVU
• 82W KU
• 91W KU
•  
• 61W Amazona
• 79W AMC2
• 83W AMC9
• 95W Galaxy 3C
• 97W Galaxy 97W
• 101W SES1
• 105W AMC 15
• 113W Sat Mex 6
• 117W Sat Mex 5
• 125W AMC 1
• 83W Hughes
• 87W Hughes

You can also update the firmware and satellite list through the USB port on your computer, as more satellites and features are added.

View Super Installer Lite PDF Manual

The instrument starts in the "Satellite Search" mode which makes it easy to detect the satellite desired. The instrument has a preset list of satellites which can be selected by using the Up/Down buttons. When a satellite is displayed, the meter immediately starts to search for that satellite.

The signal level will increase on the signal bar if any satellite signal is detected. If the beeper is enabled, then the pitch of the beeper will increase with signal strength. Once the instrument locks on a satellite transponder, the display is changed. Once locked on a transponder, the SNR (signal to noise ratio) bar and the Quality bar (derived from BER - bit error rate) are displayed.

Once “LOCKED” on a signal, the satellite is confirmed with the MPEG data stream using the TSID and ONID (transport stream ID and Original Network ID) for the chosen transponder.

The sequence of steps in locking are:

•  “Locked” is displayed and the SNR/Quality bars are shown.
•  “Found” is displayed if TSID and ONID from transponder match for the desired satellite.

If the ONID and TSID do not match, then “Wrong Satellite” is displayed alternating with the actual ONID and TSID found for this transponder. When the ONID and TSID to match are both zero, then the actual ONID and TSID are displayed. 

 The Super Installer Lite can also be updated with the European firmware and satellite list to work with the following list of satellites:

INTELSAT 12 45.E

TURKSAT 42.E

HELLASAT 39.0E

EUTELSAT W4 36.E

EUROBIRD 33.0E

ASTRA 31.E

ARABSAT 30.E

ASTRA2 28.E

ASTRA3 23.E

ASTRA1 19.E

EUTELSAT W1 16.E

HOTBIRD 13.E

EUTELSAT W1 10.E

EUROBIRD 9.E

EUTELSAT W3 7.E

SIRIUS 5.E

THOR 1.W

AMOS 4.W

ATLANTIC BIRD 5.W

NILESAT 7.W

TELECOM 8.W

ATLANTIC BIRD 12.5W

TELESTAR 15.W

INTELSAT  901 18.W

NSS 7 22.W

INTELSAT 905 24.5W

INTELSAT 907 27.5W

HISPASAT 30.W

This meter comes with the North American firmware and satellite list but can easily be updated for either.